What tankless service covers
A tankless heater heats water as it flows through a heat exchanger, so there is no tank to leak or store sediment. The price of that convenience is scale. Minerals bake onto the heat exchanger, flow drops, and the unit throws an error code or shuts off.
Service falls into three jobs: installing a new unit, repairing a faulty one, and flushing scale out of a working one. The first two are straightforward. The third is the one most owners skip, and it explains most of the failure calls.
Flush and descale: the job people forget
A flush circulates a descaling solution through the heat exchanger, usually through service valves on the unit, then rinses it. It takes a couple of hours and brings flow back to normal. Many manufacturers call for a flush every year in hard water areas.
Missouri American Water reports total hardness of 66 to 226 ppm as calcium carbonate in its 2023 St. Louis County report, depending on the treatment plant. That is moderately hard to hard water, so annual flushing is a sensible default here. A water softener cuts the scale load further.
Signs your tankless unit needs a flush
- Hot water output has weakened or turned lukewarm
- The unit shows a recurring error code about flow or temperature
- The heater makes a rumbling or popping sound while running
- Water takes longer to heat than it did when new
- It has been more than a year since the last flush
Common repair causes
| Symptom | Likely cause | Typical fix |
|---|---|---|
| Cold water between hot bursts | Flow too low to trigger the burner | Clean inlet screen, check minimum flow |
| Error code on display | Scale, sensor fault or venting fault | Descale, replace sensor, inspect vent |
| No hot water at all | Gas supply, igniter or power | Test supply, replace igniter or board |
| Water too hot or swinging | Failed thermistor | Replace the thermistor |
Tankless unit stopped working? Call to schedule a service visit.
Call (314) 461-6239Installing or converting to tankless
Gas tankless units need a gas line large enough to feed the burner at full fire, and a vent rated for the unit. Electric models need substantial amperage, and some homes need panel work. If you are switching from a tank, see the water heater installation page for the shared steps.
In a failure situation, many owners get a tank installed to restore hot water quickly and convert later. The replacement page explains that option.
What changes the price of tankless work
Cost factors we explain before work starts
- Install or flushA flush is a short, fixed-scope visit. An install involves gas, venting and mounting.
- Gas line and ventingUpsizing a gas line or running a new vent adds labor.
- Unit brandParts availability and warranty terms vary between brands.
- Scale conditionA unit that has not been flushed for years may need extra circulation time.
- SchedulingBooked daytime service is priced differently from after-hours.
Maintenance and planned installs are not covered by homeowner insurance. Call (314) 461-6239 for your actual number.
Ballwin households that suit tankless
Tankless fits households that run showers back to back, because the supply never runs out. It is a weaker choice for a home with a very small gas line or for someone who runs several fixtures at once and expects every one at full temperature.
Our dispatchers also serve Manchester and nearby homes, where the same questions about line size and venting come up with every install.
Standards note: Tankless installs follow the manufacturer's instructions and the International Plumbing Code (IPC) for venting, gas piping and condensate drains. The City of Ballwin lists the International Plumbing Code among its adopted codes, and the Building Inspections Department at (636) 227-2129 can confirm which edition applies.
Tankless water heater questions from Ballwin homeowners
Our line is open 24/7. If a unit has completely failed we dispatch a licensed plumber as soon as a crew is free, and planned flushes are scheduled for daytime visits.
Annually is common advice in hard water areas, and local water is moderately hard to hard per the utility's report. Check your manual for the maker's schedule.
We work on most common brands. Give the model number on the call so the plumber can bring likely parts.
It can reduce standby heat loss. Savings depend on usage, fuel cost and maintenance, so we avoid promising figures.
A brief burst of cold water between hot flows. It happens when the unit cycles off and on. A flow or sensor adjustment often fixes it.
Often yes, but the gas line size, vent path and electrical capacity must be checked first.
Need tankless service? Call and a licensed plumber will take your details.
Call (314) 461-6239